MineLab Offer 15% Discount For All Military Personnel, Call For Discount Information

RnB EX-3000 Lithium-Polymer Battery for Minelab Excalibur II w/ Charger

RnB EX-3000 Lithium-Polymer Battery for Minelab Excalibur II w/ Charger

Brand: Detector Supply
Item Number:

Regular price $69.99 On Sale

  • RnB EX-3000 Lithium-Polymer Battery with Wall Charger.

    Made for the Minelab Excalibur II 800 and Excalibur II 1000 Metal Detectors.

    Description

    The Only Trusted Li-Po Battery Pack Around the World!

    Hunt For Days Not Hours!

    Features

    • Get More Battery Life
    • Extend your detecting time up to 60 hours!
    • High Capacity Lithium-Polymer Delivers Long Life Run Time with Fade-Free Power!

    Compatible

    • Minelab Excalibur II 800
    • Minelab Excalibur II 1000

    Installation Instructions

      1. First remove the black soft plastic end cover that is glued to the battery pod.
      2. Very carefully insert a straightened out heavy paper clip that has been bent in half between the cover and the battery pod, moving it around to break the glue’s bond without tearing the cover.
      3. Once the cover is free, remove the cover from the pod.
      4. Mark the end cap and battery pod with a magic marker so the end cap can be replaced in the same position.
      5. Completely remove both set screws holding the end cap in the battery pod.
      6. Very carefully twist and pull the end cap out of the tube, the resistance is from the O-ring which must NOT be damaged or the pod can leak.
      7. The battery pack will now slide out of the pod, make sure there is no dirt or sand left inside the pod by wiping it clean.
      8. Disconnect the old battery pack.
      9. Very carefully remove and clean the O-ring, do NOT use any sharp instruments to remove it.
      10. Once the O-ring has been wiped clean with a soft paper towel apply silicone grease all around the O-ring sparingly, Ace Hardware 90% pure silicone grease 4095667 works well as does Sil-Glyde.
      11. Place the O-ring back into the end cap groove and connect the new battery pack, making sure the connectors are clean, optionally add some dielectric grease.
      12. Slide the new battery pack into the battery pod, if it is a tight fit due to the older pod versions taper, apply some silicone grease to the edges of the pack to insert.
      13. If a silica desiccant pack came out of the pod when opened replace it at this time.
      14. Very carefully twist and push the end cap back into the pod without pinching the O-ring, which could cause leakage.
      15. Once the end cap is back in and the magic marker lines and screw holes line up, place the set screws back in.
      16. Do NOT over tighten, snug them down firmly without stripping the threads.
      17. Place the soft black plastic end cover back on by putting two dabs of RTV silicone rubber inside it and pushing it on.
      18. Optionally you may wrap a turn and a half of electrical vinyl tape around the battery pod covering the set screw holes and let friction hold the end cover in place.
      19. Charge the new battery before use.
      20. ONLY use the supplied charger for charging the Lithium Polymer Battery

    * Lithium Polymer Battery ONLY – POD NOT INCLUDED!

    Order Confirmation:

    As soon as you place your order, you will receive an order confirmation e-mail. This means that we have received your order in our system and pre-authorized your credit card for the purchase.  As soon as we receive your order, we automatically reach out to our suppliers to confirm that it is in stock and available for immediate shipment.  If your item is on backorder or unavailable, we will void the pre-authorization and reach out to you via e-mail.  If your item(s) are available for immediate shipment (within 5 business days), we will process the charges and submit the order for shipment.

    Order Shipment:

    If your order is stock and we process the charges to your credit card, it will ship within five business days from the date of your order.  We will send you tracking information within 24 hours of your order leaving the warehouse to the e-mail address you provided when checking out.  If you do not receive tracking information from us within six business days of your order, feel free to follow up with us at iInfo@msprosdet.com

    Damages:

    Please inspect the packaging of your item(s) when they arrive, if you notice any damage you should make note of it when 

    RnB EX-3000 Lithium-Polymer Battery with Wall Charger.

    Made for the Minelab Excalibur II 800 and Excalibur II 1000 Metal Detectors.

    Description

    The Only Trusted Li-Po Battery Pack Around the World!

    Hunt For Days Not Hours!

    Features

    • Get More Battery Life
    • Extend your detecting time up to 60 hours!
    • High Capacity Lithium-Polymer Delivers Long Life Run Time with Fade-Free Power!

    Compatible

    • Minelab Excalibur II 800
    • Minelab Excalibur II 1000

    Installation Instructions

      1. First remove the black soft plastic end cover that is glued to the battery pod.
      2. Very carefully insert a straightened out heavy paper clip that has been bent in half between the cover and the battery pod, moving it around to break the glue’s bond without tearing the cover.
      3. Once the cover is free, remove the cover from the pod.
      4. Mark the end cap and battery pod with a magic marker so the end cap can be replaced in the same position.
      5. Completely remove both set screws holding the end cap in the battery pod.
      6. Very carefully twist and pull the end cap out of the tube, the resistance is from the O-ring which must NOT be damaged or the pod can leak.
      7. The battery pack will now slide out of the pod, make sure there is no dirt or sand left inside the pod by wiping it clean.
      8. Disconnect the old battery pack.
      9. Very carefully remove and clean the O-ring, do NOT use any sharp instruments to remove it.
      10. Once the O-ring has been wiped clean with a soft paper towel apply silicone grease all around the O-ring sparingly, Ace Hardware 90% pure silicone grease 4095667 works well as does Sil-Glyde.
      11. Place the O-ring back into the end cap groove and connect the new battery pack, making sure the connectors are clean, optionally add some dielectric grease.
      12. Slide the new battery pack into the battery pod, if it is a tight fit due to the older pod versions taper, apply some silicone grease to the edges of the pack to insert.
      13. If a silica desiccant pack came out of the pod when opened replace it at this time.
      14. Very carefully twist and push the end cap back into the pod without pinching the O-ring, which could cause leakage.
      15. Once the end cap is back in and the magic marker lines and screw holes line up, place the set screws back in.
      16. Do NOT over tighten, snug them down firmly without stripping the threads.
      17. Place the soft black plastic end cover back on by putting two dabs of RTV silicone rubber inside it and pushing it on.
      18. Optionally you may wrap a turn and a half of electrical vinyl tape around the battery pod covering the set screw holes and let friction hold the end cover in place.
      19. Charge the new battery before use.
      20. ONLY use the supplied charger for charging the Lithium Polymer Battery

    * Lithium Polymer Battery ONLY – POD NOT INCLUDED!

    Order Confirmation:

    As soon as you place your order, you will receive an order confirmation e-mail. This means that we have received your order in our system and pre-authorized your credit card for the purchase.  As soon as we receive your order, we automatically reach out to our suppliers to confirm that it is in stock and available for immediate shipment.  If your item is on backorder or unavailable, we will void the pre-authorization and reach out to you via e-mail.  If your item(s) are available for immediate shipment (within 5 business days), we will process the charges and submit the order for shipment.

    Order Shipment:

    If your order is stock and we process the charges to your credit card, it will ship within five business days from the date of your order.  We will send you tracking information within 24 hours of your order leaving the warehouse to the e-mail address you provided when checking out.  If you do not receive tracking information from us within six business days of your order, feel free to follow up with us at iInfo@msprosdet.com

    Damages:

    Please inspect the packaging of your item(s) when they arrive, if you notice any damage you should make note of it when